✅ Finnish wood, responsibly manufactured in Lempäälä
✅ Completely natural and safe product
✅ Light and fresh appearance
✅ Excellent resistance to moisture fluctuations
✅ PEFC-certified

Our product uses spruce, a domestic, versatile, and strong softwood that handles moisture changes well. Easy to work with and finish, spruce is ideal for interior use, saunas, and, when treated, exterior cladding. Its warm light color and straight-grained pattern make spruce an aesthetically pleasing choice for visible surfaces. Our PEFC-certified spruce products are responsibly produced and environmentally friendly.

Tilaustuote

Tilaustuote on hyvä valinta suurempiin kohteisiin, joissa tarvitaan juuri tietyn profiilin mukaista tuotetta tietyssä puulajissa. Se voidaan valita silloin, kun hankinta voidaan suunnitella riittävän ajoissa ennen varsinaista käyttötarvetta.

Tilaustuotteet valmistetaan asiakkaan tarpeiden mukaan, joten jokainen tilaus on yksilöllinen. Toimitusaikaan ja lopulliseen hintaan vaikuttavat useat tekijät, jotka huomioidaan aina erikseen tarjousta laadittaessa.

Saat tarkan tarjouksen ja toimitusarvion tilauksen sisällön varmistuttua. Mitä tarkemmat tiedot tuotteesta, määrästä ja toivotusta toteutuksesta saamme heti alussa, sitä nopeammin pystymme käsittelemään tilauksesi.

Huomioitavaa on kuitenkin, että materiaali- ja profiilivaatimusten tarkkuus vaikuttaa tuotteen valmistettavuuteen. Mitä yksityiskohtaisemmat vaatimukset ovat, sitä rajallisemmat voivat olla toteutusvaihtoehdot. Toteutettavuus arvioidaan myös saatavilla olevien raaka-aineiden perusteella.

Toimitusaika

Toimitusaikaan vaikuttaa erityisesti aihion saatavuus. Raaka-aineen saatavuus vaihtelee puulajeittain ja laatuluokittain. Suuremmat tilausmäärät edellyttävät myös enemmän valmistelua ja tuotantoaikaa, jotta tilaus voidaan aikatauluttaa osaksi tuotantoa. Tuotteen monivaiheinen valmistus, kuten höyläys, päätyponttaus ja pintakäsittely, vaikuttaa toimitusaikaan ja edellyttää pidemmän tuotantoajan.

Toimitusaika arvio kertoo, milloin tavara on valmiina lähetettäväksi tai noudettavaksi varastollamme. Vahvistamme kunkin tilauksen yksilöllisellä toimitusajalla. Alla on esimerkkejä tyypillisistä toimitusajoista erilaisille tapauksille.

Tuotteet joille toimitusaika on alkaen 2–4 viikkoa

Tämä toimitusaika on mahdollista, kun raaka-aine on valmiina ja tuotantoajankohta vastaavalle tuotteelle on lähellä, tällöin tilaus voidaan sovittaa vastaavan tuotantoajon kanssa yhteen. Muussa tapauksessa toimitusaika on vähintään 4 viikkoa. Arvio ei ota huomioon tuotantojonon ruuhkautumisia, sen on tarkoitus olla suuntaa-antava.

• Pintakäsittely
• Vakiovarastoprofiili
• Vakiovarastoprofiilin pienet muutokset, esim. leveys tai paksuus

Vakiovarastoprofiili = Mitoitukseltaan ja muodoltaan täysin sama tuote esimerkiksi toisessa puulajissa

Tuotteet, joiden toimitusaika arvioidaan tapauskohtaisesti

• Vakiovarastoprofiili, jolle ei ole varastossa raaka-ainetta
• Erikoisprofiili, jolle ei ole varastossa raaka-ainetta

Kumpikin yllä mainittu tapaus onnistuu vain laajoihin projekteihin toimitusajan ollessa vähintään 2kk

Rajoitteet

Määrän tulee olla vähintään alla mainitun mukainen.

• 500m, kun kyseessä on pintakäsiteltävä varastotuote
• 1000m, kun kyseessä on vakiovarastoprofiili
• 2000m, kun kyseessä on vakiovarastoprofiili pienillä muutoksilla
• Sahatavaranippu (n. 4m³), jos tilaus ei ole vakiovarastoprofiili
• Sahatavaranippujen (n. 4m³) kerrannaisia (1,2,3,..), kun raaka-ainetta ei ole varastossa.

Vahvuus

• Tuotteen vahvuus voi vaihdella 12-45mm välillä.

Leveys

• Tuotteen leveys voi vaihdella 40-200mm välillä.

Pituus

• Puutavaran pituus vaihtelee 1,8-6,0m välillä. Pyrimme toteuttamaan pituustoiveet mahdollisuuksien mukaan, mutta aina se valitettavasti ole mahdollista.

Hukkavara

Jotta vältät kalliin lisätilauksen, huomioi riittävä hukkavara tilauksessasi. Pienen lisätilauksen kulut voivat olla vähintään 5x alkuperäiseen nähden. Mahdollinen täydennystilauksen toteuttaminen vie vähintään yhtä kauan, kuin alkuperäisen tilauksen toteuttaminen ja täydennystilausten hinta arvioidaan omana toimituksena.

Tilattu ja toimitettava määrä

Puutavaran toimitusmäärässä sallitaan ±10 prosentin vaihteluoikeus tilausvahvistuksella annettuun määrään verrattuna. Tämä tarkoittaa, että toimitettu määrä voi olla tilattua määrää 10 prosenttia pienempi tai suurempi. Koska puutavara on luonnonmateriaali, sen ominaisuuksissa esiintyy luonnollista vaihtelua. Tästä syystä tuotannossa syntyvän hukan määrää ei voida ennakoida täysin tarkasti. Siksi valmistuvaa määrää ei voida ennakoida, vaan se selviää valmistamisen aikana ja harvoin vastaa tarkalleen tilattua määrää.

Product information

Product measurements

Product features

Sustainability

Please note that we deliver our products in bundles. Bundle size is indicated together with stock information on top right corner.

Highlighting Wood’s Best Qualities with Surface Treatment

Surface treatment brings out the best in wood and tailors high-quality timber to its intended use. Beyond durability and fire safety, it adds color that perfectly complements your project.

Durability and versatility can be further enhanced with industrial painting or finishing suited to your needs. Pre-finished or treated wood also speeds up and simplifies work during tight construction or renovation schedules.

Wood is a high-quality, versatile material that, after industrial painting or surface treatment, performs even better in various conditions. Our extensive practical experience and expertise in wood finishing guide us on how to treat material for different applications.

Not all wood requires finishing before use, but treatments can highlight specific properties. For example, sauna wood benefits from protective coatings designed to withstand high temperatures and humidity. Surface treatment can also extend a wood product’s lifespan.

The choice of treatment often depends on the wood’s application. Properly treated wood adds structure and character to interior and exterior surfaces. Opaque painting or translucent finishes allow you to achieve the exact color that best fits your interior design and overall building aesthetic.

All painting and finishing work is done in our industrial paint shop. We use water-based, eco-friendly coatings and paints from reputable manufacturers. Our fire-retardant treatments can bring wood to a B-s1, d0 fire class.

To operate as environmentally responsibly as possible, a batch must be at least 500 meters. This minimizes raw material waste and keeps our operations efficient.

Storage of Indoor Products

• Products should be acclimated in the room where they will be installed for 1–2 weeks.
• Products should be stored horizontally in unopened packages and elevated at least 30 mm from the surface.
• During storage, humidity must not exceed the normal moisture level of the installation site. The temperature should be higher than the outdoor temperature.

Note that any wet work in the space will significantly increase humidity. If products are stored in the same room, they may swell. Conversely, a construction heater dries the air and can shrink the product. Rapid drops in humidity may cause cracking in the wood. Also, if packages have been tightly stacked, the moisture content of the packages in the center and on the outside of the stack may differ.

Installation

• Plan the installation direction and possible joint locations.
• When paneling multiple walls horizontally, install panels on all walls simultaneously.
• Use fasteners suitable for the specific application.
• Sort panels by color or knots so they are evenly distributed across the surface.
• Regularly measure to ensure the installation progress remains as intended.
• If needed, consult a professional installer.

Panels are installed on the battens. The orientation of the battens depends on the paneling direction: for horizontal paneling, battens are installed vertically; for vertical paneling, battens are installed horizontally. Battens must be straight and spaced appropriately for the paneling, but no more than 600 mm apart.

When paneling multiple walls horizontally, installation progresses simultaneously on all walls, layer by layer, to ensure precise corner alignment. Fastening is recommended by nailing directly through the panel surface. Avoid hand-nailing with heat-treated products to prevent hammer marks or panel splitting. In humid areas and with heat-treated wood, use stainless steel fasteners.

Treatment

• Always treat the entire panel along its full length to avoid visible seams.
• Follow the manufacturer’s instructions carefully.
• Use a product suitable for the installation environment.
• Keep in mind that wood will “move” over time, so plan for slight dimensional changes.
• Products are available with either opaque or translucent finishes.
• Treatment can be done by painting, oiling, or varnishing.
• For translucent finishes, the product can be tinted or clear.

Due to the heat and humidity, not all interior treatment methods can be used in the sauna. Ensure the appropriate treatment by consulting the paint manufacturer.

Maintenance

• Regular cleaning keeps surfaces in good condition and looking attractive.
• Maintenance intervals depend on the product type and installation location.
• Treat surfaces in a timely manner to prevent damage due to missing protective coating.

Sauna Cleaning

A sauna stays clean when you shower before going in and use a bench towel. Keep the heater on for a short time after bathing so the sauna dries well. If possible, ventilate the sauna after every use. When vacuuming other areas of your home, also vacuum the sauna floor.

Thorough Sauna Cleaning

A deeper cleaning is needed once or twice a year. Follow these steps:

• Clean the sauna when it is cool so cleaning agents do not dry too quickly on surfaces.
• Vacuum or remove dust and loose debris from the floor and benches with a long-handled brush or scraper. Also brush the ceiling and walls.
• Wet the wooden surfaces with warm water to open the pores. Wash with a general-purpose cleaner or sauna cleaner using a soft brush or scrubbing pad. Rinse with cold water to close the pores.
• When scrubbing wood, work in the direction of the grain. Use a soft deck brush, for example. Wet and wash walls from top to bottom.
• Avoid unnecessary and excessive rubbing.
• Avoid chlorine-based cleaners, as chlorine can absorb into the wood and later be released into the air when heating the sauna.
• Air the sauna well.
• After cleaning, keep the sauna heater on for a short time so it dries completely.

For many Finns, the home sauna is a favorite place, but it demands a lot from interior materials. Temperatures can rise above 100°C, and the high humidity means that ceiling and wall panels, for example, are under heavy stress.

Lauta.fi’s versatile Tuuli Sauna product family is designed to withstand the sauna’s changing and challenging conditions. With Tuuli Sauna products, a sauna can be decorated in a stylish, timeless, or modern way—either in harmony with the rest of the home or as a distinct and unique space. They allow the home’s interior theme to continue into the sauna, or for the sauna to stand out as a completely different environment.

The range includes ceiling and wall panels, bench boards, bench facings, and bench frame posts—all of which greatly influence sauna atmosphere. It also offers finishing products such as cover, edge, shadow, corner, and ceiling mouldings, as well as boards and slats. This diverse and adaptable product family brings both ambience and durability to the sauna, enabling practical and safe solutions for tricky design spots.

While Tuuli Sauna is optimized for sauna conditions, its products are also suitable for other interior uses. Its panels, boards, and slats can be used in single-family homes, apartments, and other living spaces, making it possible to create a completely unified interior style throughout the home. Tuuli Sauna products are also used in offices, customer spaces, and public buildings. Design options are further expanded by their compatibility with the Tuuli Indoor product range for general interiors, which matches perfectly in style—though Tuuli Indoor products are not suitable for sauna use due to heat and humidity.

The extensive Tuuli Sauna range features many wood species, including giant thuja, thermo radiata pine, thermo alder, black alder, thermo aspen, aspen, thermo pine, and spruce. The natural individuality of wood—such as varying knot patterns—makes each product unique.

While interiors often feature materials like plastic, concrete, glass, or metal, Lauta.fi’s Tuuli Sauna products are natural and eco-friendly wood. They are engineered for strength and usability on par with other materials, while tolerating sauna heat and moisture exceptionally well.

Lauta.fi delivers product sample pieces to both consumer customers and professionals, such as architects, interior architects and designers, construction industry and procurement professionals.

If you are interested in ordering one or more sample pieces, please contact our sales department via email lauta@lauta.fi or phone +358 3 3123 6000 (On weekdays 8-16).